Nightmare Moon
My Little Pony : Friendship Is Magic

Cosplayer: Mad Hamster

Variant: quadsuit

Status: Complete

Condition: Not Set

24th March 2014: Nightmare Moon's body coming together Well it looks like more progress has been made, I decided that for the front legs to have the foam go all the way up my arm to give her more of a natural bend rather than rely on having PVC go all the way up and feel robotic and uncomfortable., it also means that I can grip onto the scythe much better than I would have done otherwise which is a challenge in itself.
The stomach piece literally wraps all the way around my chest and my back, and when I start sorting out the harness for the wings, the wings will attach onto the back and have extra padding to enhance the shape. But not too much or she'll look like she has a hunchback :s.
I found a very interesting problem which I will be sorting out soon which is her armour, now those who know nightmare moon will know she has armour on her head, around her neck which wraps under her chest and her hooves... the biggest problems will be her neck and head armour, but I have a few ideas ;).

The

2nd March 2014: Nightmare moon's body so far Well things have been going okay, there have been delayed because of helath but I'm fine now. So far the bits that are cut out are the front legs, the rear feet, the rump, the thighs, the tail and the wings. All of which are made out of foam. Templates have been a wonderful thing for this, they're great for helping get the proportions especially for something like this :p I still have to figure out the way of attaching the wings to the torso but it should be doable. The plan is to work on the head and next, then the arms and then the torso

1st February 2014: Nightmare Moon wings and torso Started on bits of nightmare moon's body, her hocks have been cut out but the next stage is to shape them so then they get the right shape.
I also started on her wings, they're just made out of foam for now... however there is one down side to this, with the fact that her wings are meant to stand up on end when I'm bent over it's quite tricky. I do have some options, these include wire or pipe.. still early days though :)

4th January 2014: Nightmare moon scythe part 2 The scythe is coming along very nicely now... despite some minor complications.
Once I had the blade and decoration carved up and glued to the PVC pipe, it was time to add the expanding foam... that's when things got a bit complex.
You see even though I used foam board, the core still got warped and went a bit off centre, not so much on the front bit of the blade but the back. But then again that is why it is so good to use foam board... because you can still carve that whilst carving the foam.
Once the main bit of the blade was carved I had to the decorative bit that almost wraps round the blade... so more expanding foam and hours of craving and accidental stabs later, it was done... I still need to do a tiny bit of work on it, but otherwise I can start making the whole thing look nice and smooth

22nd December 2013: Nightmare Moon Scythe Finally started on nightmare moon, I decided to give her a weapon that, although not canon in the official show, IS canon in the trailer of 'Fall of the Empire' by Silly Filly Studios so it's more for the fans really :).
I looked all over the place to find suitable tutorials on scythes and most of them were... umm... not too good, they mainly used either cardboard or didn't do things that would give a high quality scythe... or even have ways of making the blasted thing easy to transport.
Eventually I found one and that really made a difference, I found the reference I needed of the scythe itself and got some foam board. I drew out the design for the blade and cut it out. I also cut the top of the PVC pipe to accommodate the blade, the shaft and the base at the bottom, the pieces lock together with some doweling rode which will have a bit of wire in it to stop it moving and the shaft was shaped by using a heat gun and slowly bending it.
I still have quite a bit of work to do but the next step will be to shape the blade, figure out the locking system and the various other shaped pieces on the shaft and the base


otakugirl avatar

otakugirl - 4th March 2014
OMFG I wanna see this right now! I will be looking out like a hawk for this! Amazing

SilentDragonfly avatar

SilentDragonfly - 8th March 2014
This is looking damed good so far. Keep up the hard work.

Kyuipo avatar

Kyuipo - 12th March 2014
wow. this is coming along nicely. good job :3

Clockwork Dandy Noodles avatar

Clockwork Dandy Noodles - 23rd March 2014
Looking good my lovely :3 cant wait to work on projects together hehe its going to be epic :D

ManiacCos avatar

ManiacCos - 24th March 2014
I saw this on FB! Looking great :D

EvilShadowMaster avatar

EvilShadowMaster - 24th March 2014
How are you even doing this? This is truly amazing! :D I wish you good luck!!

Kei Lin Sama avatar

Kei Lin Sama - 25th March 2014
That looks incredible! Keep going!

PandoraCaitiff avatar

PandoraCaitiff - 29th May 2014
Wowsers! I'd seen the progress pics, but this is the first time I've seen the finished thing (I was too tired to attend the Masq).

That's some awesome work :)

Tsuchinoko avatar

Tsuchinoko - 29th May 2014
This looks amazing!
Fantastic job on this ^^